facebook1 youtube1 twitter1 instagram linkedin1 pinterest1

NOTICE:  If you are not a free registered member of the site, you will not see the photos in the forum, and you won't be able to access our premium member content. Please consider joining our community! REGISTER AND MAKE THIS BOX DISAPPEAR!

×

Pictures Posting Not Working (12 Jun 2023)

Picture uploads is again unavailable. We are working on the problem. Thanks for your patience.

Makotosun

RT2 Magneto Puller - Motion Pro

  • Midge0z
  • Midge0z's Avatar Topic Author
  • Offline
  • New Member
  • New Member
  • Posts: 5
  • Likes received: 0

RT2 Magneto Puller - Motion Pro was created by Midge0z

Hi Guys, does anyone know the correct Motion Pro Part Number for a Magneto Puller for an RT2 ? Thanks
11 Jul 2022 15:45 #1

Please Log in or Create an account to join the conversation.

  • Posts: 14507
  • Likes received: 10721

Replied by MarkT on topic RT2 Magneto Puller - Motion Pro

By memory 08-0026

27mm x 1.0 LH
1963 YG1-T, 1965 MG1-T, Allstate 250, 1970 CT1b, 1971 R5, 1973 AT3MX, 1974 TS400L, 1975 RD350, 1976 DT175C, 1976 Husqvarna 250CR, 1981 DT175G, 1988 DT50, 1990 "Super" DT50, 1991 RT180, 2017 XT250
11 Jul 2022 16:25 #2

Please Log in or Create an account to join the conversation.

  • Posts: 3951
  • Likes received: 2089

Replied by Makotosun on topic RT2 Magneto Puller - Motion Pro

Here is our site amazon associates link for the correct puller for the RT2 and most every Yamaha enduro except for the 125 electric start models:

amzn.to/3PdgUII
IF it isn't one thing, it's another.
11 Jul 2022 23:08 #3

Please Log in or Create an account to join the conversation.

  • Posts: 14507
  • Likes received: 10721

Replied by MarkT on topic RT2 Magneto Puller - Motion Pro

New one on me Mauser.   I've never seen any Yamaha magneto use a bolt like that.  Yamaha outer rotor magnetos on the two strokes use the same puller from 1964 to 2022 as far as I can tell....  27mm x 1.0 LH piece threads into the flywheel and then a center push bolt pops it off. 

Inner rotor Yamaha magnetos use a sort of "hollow nut" to remove.  Those ignitions were used on race machines with no lights/charging system.

Armature on a generator (125 e-start for example) or armature on an alternator (RD350 for example) can use a simple bolt but normally 10mm on a Yamaha. 
1963 YG1-T, 1965 MG1-T, Allstate 250, 1970 CT1b, 1971 R5, 1973 AT3MX, 1974 TS400L, 1975 RD350, 1976 DT175C, 1976 Husqvarna 250CR, 1981 DT175G, 1988 DT50, 1990 "Super" DT50, 1991 RT180, 2017 XT250
The following user(s) Liked this Post: Makotosun, RT360Fan, Ht1kid
12 Jul 2022 04:36 #4

Please Log in or Create an account to join the conversation.

  • Posts: 478
  • Likes received: 197

Replied by RT360Fan on topic RT2 Magneto Puller - Motion Pro

I can confirm that the RT2 uses the M27x1.0 LH puller as MarkT mentioned earlier.  
12 Jul 2022 06:29 #5

Please Log in or Create an account to join the conversation.

Moderators: yamadmin, Makotosun, DEET, Vinnie, James Hart