facebook1 youtube1 twitter1 instagram linkedin1 pinterest1

NOTICE:  If you are not a free registered member of the site, you will not see the photos in the forum, and you won't be able to access our premium member content. Please consider joining our community! REGISTER AND MAKE THIS BOX DISAPPEAR!

×

Pictures Posting Not Working (12 Jun 2023)

Picture uploads is again unavailable. We are working on the problem. Thanks for your patience.

Makotosun

DT360A carb clamps

  • Trigbe
  • Trigbe's Avatar Topic Author
  • Offline
  • Junior Member
  • Junior Member
  • Posts: 23
  • Likes received: 10

DT360A carb clamps was created by Trigbe

Looking for the clamps that attach the carb boot to the carb and airbox. Yamaha shows them NLA. I was wondering if any of the later models used a clamp that was close to the same size before I go to a hose clamp. Any recommendations would be appreciated.
Trig
04 Mar 2019 06:48 #1

Please Log in or Create an account to join the conversation.

  • Posts: 1118
  • Likes received: 692

Replied by Swoop56 on topic DT360A carb clamps

Check the part number on a site like Partzilla , and check the part number
into Ebay motorcycle parts . I'd be very surprised if you don't get a result .
With the part number , there may be a superceded number and original number .
Check them both , as NOS stock is more likely held with the original number .
04 Mar 2019 11:42 #2

Please Log in or Create an account to join the conversation.

  • Trigbe
  • Trigbe's Avatar Topic Author
  • Offline
  • Junior Member
  • Junior Member
  • Posts: 23
  • Likes received: 10

Replied by Trigbe on topic DT360A carb clamps

Tried all of the above. The problem is Yamaha does not list clamps by adjustment range so no way to cross check other models.
Trig
04 Mar 2019 11:55 #3

Please Log in or Create an account to join the conversation.

  • MarkT
  • MarkT's Avatar
  • Away
  • Site Supporter
  • Site Supporter
  • Posts: 13387
  • Likes received: 9253

Replied by MarkT on topic DT360A carb clamps

What are the diameters you need?
1963 YG1-T, 1965 MG1-T, Allstate 250, 1970 CT1b, 1971 R5, 1973 AT3MX, 1974 TS400L, 1975 RD350, 1976 DT175C, 1976 Husqvarna 250CR, 1981 DT175G, 1988 DT50, 1990 "Super" DT50, 1991 RT180, 2017 XT250
04 Mar 2019 13:51 #4

Please Log in or Create an account to join the conversation.

  • Posts: 1118
  • Likes received: 692

Replied by Swoop56 on topic DT360A carb clamps

There are a couple on Ebay
# 362560438644 NOS Clamp
# 113598236575 Used clamp and rubber boot
NB The original part number is common to RT 1/2/3 so some members here could very well
have used clamps on parts bikes
04 Mar 2019 16:09 #5

Please Log in or Create an account to join the conversation.

  • Posts: 3971
  • Likes received: 1907

Replied by Gr8uncleal on topic DT360A carb clamps


Rendering Error in layout Message/Item: fopen(http://open.api.ebay.com/shopping?callname=GetSingleItem&appid=makotosu-08bc-47da-8e7d-68e3ee6e51ca&siteid=0&responseencoding=JSON&ItemID=201819475647&version=889&trackingid=&trackingpartnercode=9): failed to open stream: Connection refused. Please enable debug mode for more information.

Please Log in or Create an account to join the conversation.

  • Posts: 3971
  • Likes received: 1907

Replied by Gr8uncleal on topic DT360A carb clamps

Right, just been into the garage to take a photo and do some measurements.

First up, I'm assuming that it's the identical clamps for each end of this hose/joint that you are looking for Trigbe?

Just to confirm, the part number was originally 308-14455-00, superseding to 90460-54062.

The external diameter of the hose is 2 and 1/8 of an inch (2.125"), maybe a smidge over.

The downside of getting aftermarket parts from 2Fast Moto is that they are black, whereas the originals were bare metal (see second picture nabbed off ebay).

I hope that this helps.

06 Mar 2019 03:31 #7

This message has attachments images.
Please log in or register to see it.

Please Log in or Create an account to join the conversation.

  • Posts: 7
  • Likes received: 0

Replied by maraakate on topic DT360A carb clamps

Heya,

I'm also looking for these clamps as they are also used on the DT250A.  There's two from Canada, but I'm not interested in spending $30 shipped for two clamps to USA.  Does anyone know of aftermarket ones that will fit?  Being black instead of bare metal is OK.
10 Jun 2021 16:12 #8

Please Log in or Create an account to join the conversation.

Moderators: yamadminMakotosunDEETVinnieJames Hart