×
Pictures Posting Not Working (12 Jun 2023)
Picture uploads is again unavailable. We are working on the problem. Thanks for your patience.
Makotosun
Dt 360 a couple of questions
- treeves
- Topic Author
- Away
- Site Supporter
- Posts: 109
- Likes received: 48
Dt 360 a couple of questions was created by treeves
Put the original blinkers on bike I took off in 1974, the lights light but do not blink. I did buy new bulbs, did the same thing, so I bought a flasher relay off of ebay it is 6 volts. The relay did not come with directions. Would anyone know how I would connect the wires?
I have put about 200 miles on the bike since I finished. I have bored the bike back in late 70s and have not taken head off since. The bike cranks in 2 to 3 kicks when cold. I can ride the bike a few miles and leave the bike off for 30 minutes and when trying to crank it may take maybe 10 times, also feels like it has very little compression. When cranks seems to run good but I do notice after hot the bike will hesitate at about 2500 rpm and then after a few seconds idles fine. I am going to do a pressure test and see if the motor has an air leak and after that is fixed I will check cylinder and piston.
Is there anything else I need to check?
I have put about 200 miles on the bike since I finished. I have bored the bike back in late 70s and have not taken head off since. The bike cranks in 2 to 3 kicks when cold. I can ride the bike a few miles and leave the bike off for 30 minutes and when trying to crank it may take maybe 10 times, also feels like it has very little compression. When cranks seems to run good but I do notice after hot the bike will hesitate at about 2500 rpm and then after a few seconds idles fine. I am going to do a pressure test and see if the motor has an air leak and after that is fixed I will check cylinder and piston.
Is there anything else I need to check?
15 Nov 2020 10:33
#1
This message has attachments images.
Please log in or register to see it.
Please Log in or Create an account to join the conversation.
- MarkT
- Offline
- Site Supporter
- Posts: 13563
- Likes received: 9396
Replied by MarkT on topic Dt 360 a couple of questions
Do those flasher terminals have any markings?
1963 YG1-T, 1965 MG1-T, Allstate 250, 1970 CT1b, 1971 R5, 1973 AT3MX, 1974 TS400L, 1975 RD350, 1976 DT175C, 1976 Husqvarna 250CR, 1981 DT175G, 1988 DT50, 1990 "Super" DT50, 1991 RT180, 2017 XT250
15 Nov 2020 10:46
#2
Please Log in or Create an account to join the conversation.
- Gr8uncleal
- Away
- Site Supporter
- Posts: 4061
- Likes received: 1993
Replied by Gr8uncleal on topic Dt 360 a couple of questions
Flasher relay instructions below, courtesy of MarkT!
With modern replacements it makes no difference, but be aware that modern three pin relays are not the same as original Yamaha ones. You only really need a two pin one and the brown wire goes to the pin marked B or X and the Brown/White to the pin marked L.
Others will come back regarding engine issues, but check that the decompression valve is closing ok.
With modern replacements it makes no difference, but be aware that modern three pin relays are not the same as original Yamaha ones. You only really need a two pin one and the brown wire goes to the pin marked B or X and the Brown/White to the pin marked L.
Others will come back regarding engine issues, but check that the decompression valve is closing ok.
15 Nov 2020 10:48
#3
Please Log in or Create an account to join the conversation.
- treeves
- Topic Author
- Away
- Site Supporter
- Posts: 109
- Likes received: 48
Replied by treeves on topic Dt 360 a couple of questions
Mark the flasher terminals have no markings.
15 Nov 2020 10:54
#4
Please Log in or Create an account to join the conversation.
- MarkT
- Offline
- Site Supporter
- Posts: 13563
- Likes received: 9396
Replied by MarkT on topic Dt 360 a couple of questions
To add to what Alan posted, do not connect the black wire to the "extra" flasher terminal... (probably marked "P" for "pilot") If you do, you'll have a direct short when you switch on the turn signal.
You'll need to insulate the third flasher terminal (usually the one that's 90 degrees from the other two) so it cannot contact anything.
You'll need to insulate the third flasher terminal (usually the one that's 90 degrees from the other two) so it cannot contact anything.
1963 YG1-T, 1965 MG1-T, Allstate 250, 1970 CT1b, 1971 R5, 1973 AT3MX, 1974 TS400L, 1975 RD350, 1976 DT175C, 1976 Husqvarna 250CR, 1981 DT175G, 1988 DT50, 1990 "Super" DT50, 1991 RT180, 2017 XT250
15 Nov 2020 10:55
#5
Please Log in or Create an account to join the conversation.
- Pedalcrazy
- Offline
- Platinum Member
- Posts: 689
- Likes received: 452
Replied by Pedalcrazy on topic Dt 360 a couple of questions
1978 DT400E
1976 DT400C
1973 RT3
1971 RT1B
1968 DT1 (3)
1976 DT400C
1973 RT3
1971 RT1B
1968 DT1 (3)
The following user(s) Liked this Post: MarkT, Swoop56
15 Nov 2020 11:42
#6
Please Log in or Create an account to join the conversation.
- Gr8uncleal
- Away
- Site Supporter
- Posts: 4061
- Likes received: 1993
Replied by Gr8uncleal on topic Dt 360 a couple of questions
Yes, mis-matched wattage could be the issue. The same indicators had different wattage bulbs and relays, depending on where in the world you were - UK bikes at that time tended to get 8w.
15 Nov 2020 12:51
#7
Please Log in or Create an account to join the conversation.
Moderators: yamadmin, Makotosun, DEET, Vinnie, James Hart