×
Pictures Posting Not Working (12 Jun 2023)
Picture uploads is again unavailable. We are working on the problem. Thanks for your patience.
Makotosun
couple of questions
- wayno
- Topic Author
- Offline
- Premium Member
- Posts: 88
- Likes received: 10
couple of questions was created by wayno
I have a U.S spec dt400c that I am rebuilding, found out today that the brake cable I bought a couple of months ago don't fit, it has the 8mm thread not the 6mm so am wondering if it's for the mx version? also the clutch cable doesn't seem long enough, tried routing it through the middle of the top yoke and along side but seems too short. next is a wiring question, when I stripped it down months ago I marked up the wires with masking tape A-A etc, putting it back I have a pink wire from the left handlebar cluster with nowhere obvious to go, any idea?
thanks Wayne.
thanks Wayne.
14 Apr 2020 08:37
#1
Please Log in or Create an account to join the conversation.
- wayno
- Topic Author
- Offline
- Premium Member
- Posts: 88
- Likes received: 10
Replied by wayno on topic couple of questions
sorted the wiring bit, it's the horn I believe.
14 Apr 2020 08:56
#2
Please Log in or Create an account to join the conversation.
- MarkT
- Away
- Site Supporter
- Posts: 13502
- Likes received: 9351
Replied by MarkT on topic couple of questions
Yes, pink grounds the horn when button is pressed... there is also a brown wire to horn that is battery DC power with key on.
1963 YG1-T, 1965 MG1-T, Allstate 250, 1970 CT1b, 1971 R5, 1973 AT3MX, 1974 TS400L, 1975 RD350, 1976 DT175C, 1976 Husqvarna 250CR, 1981 DT175G, 1988 DT50, 1990 "Super" DT50, 1991 RT180, 2017 XT250
14 Apr 2020 11:52
#3
Please Log in or Create an account to join the conversation.
- RT325
- Offline
- Platinum Member
- Posts: 9720
- Likes received: 3971
Replied by RT325 on topic couple of questions
Just be super careful fitting brake cables that are too short to go the normal route. As when suspension is compressed & rebounds you 'could' get it caught on something [top fork yoke clamp bolt] [handlebar clamp bolts] etc then it'll pull the front brake on with unintended results.
14 Apr 2020 16:30
#4
Please Log in or Create an account to join the conversation.
- wayno
- Topic Author
- Offline
- Premium Member
- Posts: 88
- Likes received: 10
Replied by wayno on topic couple of questions
didn't get as far as fitting for length on the front brake as the thread was too big, it's the clutch cable too short or I got the route wrong.
15 Apr 2020 01:17
#5
Please Log in or Create an account to join the conversation.
- Gr8uncleal
- Offline
- Site Supporter
- Posts: 4017
- Likes received: 1952
Replied by Gr8uncleal on topic couple of questions
Morning Wayne and I hope that you and yours are all ok.
Did you buy genuine Yamaha or repro?
Did you buy genuine Yamaha or repro?
15 Apr 2020 01:51
#6
Please Log in or Create an account to join the conversation.
- Fatthomas
- Offline
- New Member
- Posts: 3
- Likes received: 2
Replied by Fatthomas on topic couple of questions
Yes you just find out that MX parts won't fit. Even if look the same they are not .
15 Apr 2020 12:51
#7
Please Log in or Create an account to join the conversation.
- wayno
- Topic Author
- Offline
- Premium Member
- Posts: 88
- Likes received: 10
Replied by wayno on topic couple of questions
yes thankfully we are ok, bought them repro, ordered another from yambits but checked first on the thread size.
18 Apr 2020 09:52
#8
Please Log in or Create an account to join the conversation.
Moderators: yamadmin, Makotosun, DEET, Vinnie, James Hart