×
Pictures Posting Not Working (12 Jun 2023)
Picture uploads is again unavailable. We are working on the problem. Thanks for your patience.
Makotosun
LT2 stator/flywheel
- yamahahaha
- Topic Author
- Offline
- Site Supporter
- Posts: 966
- Likes received: 275
LT2 stator/flywheel was created by yamahahaha
Can a LT2 stator/flywheel be used on a HT1 ?
30 Dec 2023 16:08
#1
Please Log in or Create an account to join the conversation.
- RT325
- Away
- Platinum Member
- Posts: 9738
- Likes received: 3981
Replied by RT325 on topic LT2 stator/flywheel
I can only say probably, the LT2 being just a reed valve HT1 sort of.
It's when you get to mag model AT1's & CT1 that everything gets bigger.
So i'm no help sorry.
It's when you get to mag model AT1's & CT1 that everything gets bigger.
So i'm no help sorry.
30 Dec 2023 16:48
#2
Please Log in or Create an account to join the conversation.
- MarkT
- Offline
- Site Supporter
- Posts: 13512
- Likes received: 9361
Replied by MarkT on topic LT2 stator/flywheel
Pretty sure the answer is yes and also pretty sure the HT/LT is the same size crank and stator as CT
1963 YG1-T, 1965 MG1-T, Allstate 250, 1970 CT1b, 1971 R5, 1973 AT3MX, 1974 TS400L, 1975 RD350, 1976 DT175C, 1976 Husqvarna 250CR, 1981 DT175G, 1988 DT50, 1990 "Super" DT50, 1991 RT180, 2017 XT250
The following user(s) Liked this Post: Ht1kid
30 Dec 2023 17:48
#3
Please Log in or Create an account to join the conversation.
- RT325
- Away
- Platinum Member
- Posts: 9738
- Likes received: 3981
Replied by RT325 on topic LT2 stator/flywheel
LT2 has a 6304 on the mag side & CT2 has a 6205, therefore 125 also has a 6205.
Can't varify crank taper though.
Mag nuts are a different number but don't suppose that means a lot.
Not sure if i'm helping or hindering lol.
Can't varify crank taper though.
Mag nuts are a different number but don't suppose that means a lot.
Not sure if i'm helping or hindering lol.
30 Dec 2023 18:49
#4
Please Log in or Create an account to join the conversation.
- MarkT
- Offline
- Site Supporter
- Posts: 13512
- Likes received: 9361
Replied by MarkT on topic LT2 stator/flywheel
100 was built on the same basic starting size 125/175 center case casting with a shorter stroke crank and some other differences. Easy swap as far as engine mounts are concerned. I wanted to put a CT engine in my LT2 when I was a kid.
Partzilla shows same mag assembly for HT and LT
www.partzilla.com/product/yamaha/277-813...0358943085ae3514032a
Flywheel is the same for HT/LT/CT
www.partzilla.com/product/yamaha/315-813...0358943085ae3514032a
Source and lighting coils- same (CT has a different lighting coil than HT/LT)
www.partzilla.com/product/yamaha/277-813...0358943085ae3514032a
www.partzilla.com/product/yamaha/277-813...0358943085ae3514032a
Partzilla shows same mag assembly for HT and LT
www.partzilla.com/product/yamaha/277-813...0358943085ae3514032a
Flywheel is the same for HT/LT/CT
www.partzilla.com/product/yamaha/315-813...0358943085ae3514032a
Source and lighting coils- same (CT has a different lighting coil than HT/LT)
www.partzilla.com/product/yamaha/277-813...0358943085ae3514032a
www.partzilla.com/product/yamaha/277-813...0358943085ae3514032a
1963 YG1-T, 1965 MG1-T, Allstate 250, 1970 CT1b, 1971 R5, 1973 AT3MX, 1974 TS400L, 1975 RD350, 1976 DT175C, 1976 Husqvarna 250CR, 1981 DT175G, 1988 DT50, 1990 "Super" DT50, 1991 RT180, 2017 XT250
The following user(s) Liked this Post: Snglsmkr, Ht1kid
31 Dec 2023 05:24
#5
Please Log in or Create an account to join the conversation.
- yamahahaha
- Topic Author
- Offline
- Site Supporter
- Posts: 966
- Likes received: 275
Replied by yamahahaha on topic LT2 stator/flywheel
Thank you guys
31 Dec 2023 05:49
#6
Please Log in or Create an account to join the conversation.
- RT325
- Away
- Platinum Member
- Posts: 9738
- Likes received: 3981
Replied by RT325 on topic LT2 stator/flywheel
Make that thankyou Mark!!.
I must learn or remember to scroll down on partzilla to see what fits what.
I must learn or remember to scroll down on partzilla to see what fits what.
01 Jan 2024 01:34
#7
Please Log in or Create an account to join the conversation.
Moderators: yamadmin, Makotosun, DEET, Vinnie, James Hart