facebook1 youtube1 twitter1 instagram linkedin1 pinterest1

NOTICE:  If you are not a free registered member of the site, you will not see the photos in the forum, and you won't be able to access our premium member content. Please consider joining our community! REGISTER AND MAKE THIS BOX DISAPPEAR!

tools

  • maxx2395
  • maxx2395's Avatar Topic Author
  • Offline
  • Junior Member
  • Junior Member
  • Posts: 15
  • Likes received: 0

tools was created by maxx2395

HI
I am looking for clutch hub  and basket holder for a 1972 at2
any suggestions ?
Thanks in advance .
Maxx . . . . .


 
13 May 2022 13:30 #1

Please Log in or Create an account to join the conversation.

  • Posts: 84
  • Likes received: 76

Replied by mike8162 on topic tools

I have always wedged a penny between the primary gear and the cog on the basket. 
Cheers
13 May 2022 15:16 #2

Please Log in or Create an account to join the conversation.

  • Posts: 1268
  • Likes received: 909

Replied by 1971DT250 on topic tools

Motion Pro Universal Clutch Holding Tool 08-0008
 


Available from many sources.
The hours spent riding my Enduros is not deducted from my life span.
The following user(s) Liked this Post: JayB, ktfun219
13 May 2022 15:56 #3

This message has an attachment image.
Please log in or register to see it.

Please Log in or Create an account to join the conversation.

  • Posts: 11768
  • Likes received: 6969

Replied by MarkT on topic tools

+1 on the Motion Pro tool for holding inner clutch hub.. 

I would never use any tool to hold the outer hub...  use the gear jam method mentioned above and in the manual. 
1963 YG1-T, 1965 MG1-T, Allstate 250, 1970 CT1b, 1971 R5, 1973 AT3MX, 1974 TS400L, 1975 RD350, 1976 DT175C, 1976 Husqvarna 250CR, 1981 DT175G, 1988 DT50, 1990 "Super" DT50, 1991 RT180, 2017 XT250
The following user(s) Liked this Post: ktfun219
13 May 2022 18:47 #4

Please Log in or Create an account to join the conversation.

  • Posts: 7783
  • Likes received: 2854

Replied by RT325 on topic tools

Might just mean hub to undo the center nut. Rattle gun & hold it with a glove & she'll spin off easy. In gear & brake hard on might do it but not a good idea. Could leave all the plates in without the pressure plate & just put hard finger pressure on the plates would hold it for a rattle gun.
13 May 2022 20:04 #5

Please Log in or Create an account to join the conversation.

  • Posts: 1100
  • Likes received: 342

Replied by asco on topic tools

I have the AT1 - CT1 DEET TOOL

a
YAMA-LAND RESTORATIONS, 818-521-2109 This email address is being protected from spambots. You need JavaScript enabled to view it. 1971 CT1-C (BRANDY) 1970 DT1-C (MONICA) 1973 100cc Hodaka Combat Rat (ABBY NORMAL) 1972 AT2M (ARNOLD ZIFFLE)
The following user(s) Liked this Post: JGersh
14 May 2022 06:09 #6

Please Log in or Create an account to join the conversation.

Moderators: yamadminEnduronutMakotosunDEETVinnieDevinJames Hart